eufyMake E1 Enclosure Table — Guaranteed-Fit Workstation Stand

An enclosure contains the fumes. It doesn't make them disappear.

UV ink smells like UV ink, and the E1 runs its cleaning cycles whether you're printing or not. The enclosure's job is to concentrate those emissions where a duct or a filter can take them — which means the workstation under it has one job of its own: give the air somewhere to go.

Where the exhaust port points, whether the 4-inch run reaches a window or a filter without a kink, whether the intake can actually breathe — those are bench decisions. And with the XL enclosure they come with a second, blunter problem: it's 35 inches deep, which is deeper than nearly every desk it will ever be offered.

The extraction path is part of the workstation, not an accessory to it. This table is sized so the enclosure, the duct, and the room all get what they need — including a top deep enough that nothing hangs off the back.

Cut to your enclosure. Not to a category.

The top extends exactly half an inch past the enclosure on every side. Enough overhang to level, latch, and grip. Not so much that you've bought a piece of furniture you have to find room for.

• Standard — 28.15" × 20" top, 32" height. Fits the E1 enclosure at 27.15 × 19 × 17.75 in.
• XL — 28.15" × 36" top, 32" height. Fits the E1 A3 + rotary enclosure at 27.15 × 35 × 17.75 in, fully supported to the back edge.

The 32-inch frame is deliberate: the E1 enclosure is short, so a slightly taller table keeps media loading and the print bed at working height.

See the full enclosure table fitment guide for every machine we build for.

Built on 40-series black aluminum extrusion with cast corner brackets and M8 hardware — the same structural system used for CNC machine frames and industrial workstations. The top is 3/4″ melamine: flat, sealed, wipes clean, and won't telegraph a heat cycle the way a raw wood top will.

Rated for what's actually on it

An E1, its enclosure, ink, and media are steady weight with a moving carriage on top. This frame is specified for a 120 lb working load with margin for motion — because the number that matters isn't what the table holds sitting still, it's what it holds while a fast machine throws mass around on top of it.

Four leveling feet handle a floor that isn't as flat as you think it is. A machine that rocks a millimeter is a machine that ghosts.

The air you're standing in

This is the page where the air section isn't boilerplate. UV printing releases VOCs during curing, and the enclosure exists to hold them at the source. The table's open frame gives the duct a straight run from any of the enclosure's exhaust ports, the T-slot channels carry cable and hose alike, and the footprint leaves the routing decision — window, filter, or fan — to you instead of forcing it. If other people share the room with this machine, that path is the difference between contained and merely covered.

Optional: locking enclosed compartment

Add a fully enclosed mid-shelf with clear acrylic panels and a cam lock. Filament, dryers, nozzles, tools, and spares stay visible, dust-free, and secured.

If you run this machine in a classroom, a shared lab, a makerspace, or any shop where more than one person walks past it, you already know why that's on the list. Consumables walk. This is the version of the answer that doesn't involve a plastic bin and hope.

It outlives the printer

Your E1 will not be your last machine. Two years from now there's a faster one with a different footprint, and the bench you bought for this one is either the right size by luck or it's scrap. Extrusion doesn't work that way. Every surface of this frame is a mounting rail. Re-drop the T-nuts, move a rail, add a shelf, hang a spool holder, bolt on a monitor arm, restretch it for the next machine. It reconfigures because it was designed to be reconfigured.

You're not buying a table for a printer. You're buying the bench that survives the next three.

Ships flat. Assembles with one hex key.

Every extrusion arrives cut to final length, deburred, and labeled, with the leg bores already tapped for the feet. The top and shelf come CNC-cut with the mounting holes counterbored. Brackets, T-nuts, and hardware are counted and bagged by step. Flat-pack keeps the freight sane and keeps the price honest — you're paying for aluminum and precision, not for air in a box.

Assembly is straightforward and takes one person about an hour. No welding, no drilling, no cutting. If you can build the enclosure, you can build this.

Made in Rocklin, California

Cut, kitted, and shipped by the same shop that makes your enclosure. Same tolerances, same people, same phone number when you have a question. Backed by our 100% satisfaction guarantee and a 1-year warranty against manufacturer defects.

Not running an E1? We build these for any enclosure in our catalog, and for machines that aren't. Send us your model and we'll confirm the exact footprint, height, and load rating before you order.